Geothermal

Peak Pipe Systems supply GSHP contractors, drillers, installers, consultants and system designers with all the
products and services needed to extract heat from the ground and convey it to a ground source heat pump.

Peak Pipe Systems extrudes pipe, assembles ground loops and fabricates all its manifolds and chambers: all on the same ten acre site in Chesterfield.

By holding healthy stocks all year round, Peak Pipe Systems offer great lead times on the majority of their product range.

This in turn gives customers practical solutions that meet their delivery demands.

Products/Services:

  • PE pipework
  • Ground loops (single and dual wound)
  • Domestic pre-fabricated chambers
  • Modular chambers (load bearing)
  • Assembled manifolds
  • Electrofusion and Spigot fittings
  • Ancillaries
  • Bespoke design
  • Test equipment

Ground Loops

All Peak Pipe Systems ground loops (also referred to as ground probes) are supplied with factory assembled and tested U-bends to ensure optimal times and quality on site.

Ground Loops are available in the following specifications:

  • Extruded from virgin PE100 polymer
  • 25mm, 32mm or 40mm diameter SDR11 Pipe
  • Single, double of coaxial loops
  • Depth marked every meter
  • Dual wound to ease installation
  • Tested in accordance with BS EN12201 for use at 16 bar for 50 years
U-Bend
U-Bend
Ground Loops
Ground Loops

Commercial Manifolds

Peak Pipe Systems engineers and designers work with you to design and fabricate manifolds for your commercial ground source requirements.

Using 3d software, Peak Pipe Systems enables you to check your manifold before it is fabricated in our BS EN ISO 9001 accredited facility.

Geothermal fabrications for source heat pumps.
Commercial Manifold
Commercial Manifold
Commercial Manifold

Products commonly used by Peak Pipe Systems in commercial manifolds include:

  • Flow meters
  • Automatic air filters
  • Structural chambers
  • Access ladders
  • Excavation fans
  • Sump pumps
  • Dirt separators

Domestic Chambers

Peak Pipe Systems designs and fabricates standard and bespoke ground source manifolds.  A selection of these chambers are listed below, additional chambers are available.  Please contact us to discuss your requirements further.

GEOECO Chamber
GEOECO Chamber

GEOECO Chamber

  • Available in 1-way to 4-way
  • 500 x 500 x 850mm chamber
  • 63mm PE100 SDR11 header pipes
  • 40mm PE100 SDR11 outlets
  • 1″ Ball valves on flow manifold
  • 1″ flowmeters on return manifold (15-38 ltr/min)
  • 1″ BSP female filling / purging points
  • Fully sealed water resistant chamber
  • Galvanised steel pedestrian rated lid
  • Ideal for domestic systems
GEODUO Chamber
GEODUO Chamber

GEODUO Chamber

  • Available in 6-way to 12-way
  • 750 x 750 x 800mm chamber
  • 63mm PE100 SDR11 header pipes
  • 40mm PE100 SDR11 outlets
  • DN50 NP16 ductile iron isolation butterfly valves
  • 1″ Ball valves on flow manifold
  • 1″ flowmeters on return manifold (15-38 ltr/min)
  • 1″ BSP female filling / purging points
  • One shot rotational moulded chamber
  • Available with 200Kg or D400 (40T) load bearing lid
  • Horizontal orientated outlets
GEOEST 125x63 Chamber
GEOEST 125x63 Chamber

GEOEST125X63 Chamber

  • Available in 2-way to 6-way
  • 535 x 535 x 1100mm chamber
  • 63mm PE100 SDR11 header pipes
  • 40mm PE100 SDR11 outlets
  • 1″ Ball valves on flow manifold
  • 1″ flowmeters on return manifold (15-38 ltr/min)
  • 1″ BSP female filling / purging points
  • Injection moulded modular chamber
  • B125 concrete infill lid (12.5T)
  • Ideal for driveway installations
  • No base plate, to be bedded on concrete base